Fisher Price High Chair P9043 User Manual

P9043  
 
Assembled Parts  
IMPORTANT! Please remove all parts from the package and identify them before assembly.  
Tray  
Rear Base  
Front Base  
Hint: Do not remove the plastic inserts  
inside the tubes of the front base.  
Seat with Restraint  
Seat Support  
Footrest  
Seat Back with Restraint  
Seat Back Pad  
2 Frames  
Seat Pad  
Hint: Do not remove the plastic  
insert inside the tube in each frame.  
FASTENERS SHOWN ACTUAL SIZE  
#8 x ¾" Screw with Plastic Retainer – 4  
#8 x ¾" Screw – 4  
Note: Tighten and loosen all screws with a Phillips screwdriver.  
Do not over-tighten the screws.  
3
 
Assembly  
CAUTION  
This package contains small parts  
in its unassembled state.  
Adult assembly is required.  
IMPORTANT! Before assembly and each use, inspect this  
product for damaged hardware, loose joints, missing parts or  
sharp edges. DO NOT use if any parts are missing or broken.  
Contact Fisher-Price® for replacement parts and instructions  
if needed. Never substitute parts.  
2
• Fit a #8 x ¾" screw with retainer into the rear base and tighten.  
• Repeat steps 1 and 2 to assemble the other frame to the rear base.  
Tapered Frame Tube  
Seat Support  
Frame Tubes  
Rear Base  
Frame Latches  
1
• With the Fisher-Price® logo facing out, fit the tapered frame tube  
into the rear base.  
Frame Assembly  
3
• Lay the frame assembly down with long frame tubes up.  
• Position the seat support with the frame latches down.  
• Slide the seat support onto the frame tubes.  
Hint: Push the seat support all the way to the top of the assembly.  
You will hear several "clicks".  
4
 
Assembly  
Seat Support  
Footrest  
Front Base  
4
• Fit the front base into the frame tubes.  
6
• Lift the frame assembly upright.  
• Fit the footrest onto the seat support, as shown.  
5
• Insert two #8 x ¾" screws with retainers into the holes in each  
frame tube and tighten.  
Hint: If you cannot insert the screws into the frame tubes, you have  
assembled the front base backwards. Remove it, turn it around and  
re-assemble it to the frame tubes.  
Footrest  
7
• Insert two #8 x ¾" screws into the holes on each side of the  
footrest and tighten.  
5
 
Assembly  
Pegs  
Tab  
Tab  
Slot  
Seat Pad  
Slot  
Elastic Straps  
8
• At an angle, fit the tabs on the seat back into the slots in the seat.  
• Push the seat back to “snap” in place.  
• Pull on the seat back to be sure it is secure to the seat bottom.  
10  
• Pull the waist restraint ends through the slots in the seat pad.  
• Fit the elastic loops on the seat pad down through the slots in  
the seat.  
• Turn the seat upside down.  
• Pull the elastic straps through the slots in the seat and fit the  
elastic straps to the pegs.  
9
• Unbuckle the lower restraint.  
11  
• Pull the shoulder restraint ends through the slots in the seat pad.  
• Fit the straps on the back of the seat back pad into the slots in the  
seat back.  
6
 
Assembly  
Lower Shoulder  
Belt Slots  
Straps  
12  
14  
• Press to fasten the straps to secure the seat back pad.  
Smaller Baby  
• Insert the ends of the shoulder belts through the lower slots in the  
pad and seat back.  
Upper Shoulder  
Belt Slots  
13  
15  
• To adjust the restraint height for baby, push to remove the  
shoulder restraints from the seat back.  
Larger Baby  
• Insert the ends of the shoulder belts through the upper slots  
in the pad and seat back.  
7
 
Assembly  
Securing Your Child  
WARNING  
Prevent serious injury or death from  
falls or sliding out:  
• Only use for a child capable of sitting  
upright unassisted.  
• NEVER leave child unattended.  
High Chair Use:  
• ALWAYS secure child with restraint  
belts adjusted to fit your child snugly.  
The tray is not designed to hold child  
in the product.  
When attached to adult chair:  
• Use restraint belts until child is able to  
get in and out of the product without  
help (about 21/2 years old).  
Slots  
16  
• Fit the "T" end of each shoulder belt through the slots in the  
lower restraint.  
Seat Assembly  
Frame Assembly  
17  
• Place the seat assembly on the frame assembly and push to lock  
in place. You should hear a "click".  
Note: The seat assembly will only fit on the frame assembly if the  
chair attachment strap door is closed. If the seat assembly does not  
lock onto the frame assembly, check to make sure the sliding door  
under the seat is completely closed.  
8